Volume 2, Issue 3, September 2017, Page: 58-68
CFD Study to Enhance the Heat Transfer in Heat Exchanger by Change the Outer Surface of the Inner Tube and Use Nano Fluid
Zena K. Kadhim, Mechanical Engineering Department, Wasit University, Wasit, Iraq
Safaa Abed Mohammad, Mechanical Engineering Department, Wasit University, Wasit, Iraq
Received: Feb. 21, 2017;       Accepted: Mar. 6, 2017;       Published: Apr. 19, 2017
DOI: 10.11648/j.es.20170203.12      View  1725      Downloads  180
Abstract
In the present work the analysis of three different copper tubes (smooth tube, two corrugated tubes with corrugated ratio (z/d=1 and 0.5)) in a shell and tube heat exchanger done by ANSYS FLUINT14.0. This work deals with theoretical investigation was to evaluate the benefit of changing the shape of inner tube in the heat exchanger and the improving the heat transfer using water as the working fluid in the first case, then using a Nano fluids as a heat transfer working fluid. The conditions used in the simulation are in the two case the hot side flow rate range from (1 to 5 LPM) with three different temperature (40, 50 and 60°C). The cold side flow rate range (3 to 7LPM) for water and (3.2 to 7.2LPM) for nano fluid because of the change in density by added nanoparticles and at 25°C for the two cases. The simulation show results of enhancement in heat transfer rate ranging from (58.24% to 59.55%) at a temperature of 40°C, (55.62% to 58.09%) at a temperature of 50°C and (54.44% to 59.17%) at a temperature of 60°C, for both corrugated tubes with respect to smooth tube by used water as cooling fluid. By using Nano- fluid the enhancement in heat transfer are (60.14% to 61.44%) at a temperature of 40°C, (58.36% to 62.01%) at a temperature of 50°C and (56.46% to 63.15%) at a temperature of 60°C, for both corrugated tubes with respect to smooth tube.
Keywords
Heat Exchanger, Corrugated Tube, Nano-Fluid
To cite this article
Zena K. Kadhim, Safaa Abed Mohammad, CFD Study to Enhance the Heat Transfer in Heat Exchanger by Change the Outer Surface of the Inner Tube and Use Nano Fluid, Engineering Science. Vol. 2, No. 3, 2017, pp. 58-68. doi: 10.11648/j.es.20170203.12
Copyright
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
Resat Selbaşa, Önder Kızılkana, Marcus Reppichb, “A new design approach for shell-and-tube heat exchangers using genetic algorithms from economic point of view”, Chemical Engineering and Processing: Process Intensification, Volume 45, Issue 4, April 2006, Pages 268–275.
[2]
Kevin M. Lunsford, “Increasing Heat Exchanger Performance”, Bryan Research and Engineering, Inc. – Technical Papers, Bryan, Texas, 1998.
[3]
B. Chandra Sekhar, D. Krishnaiah, F. Anand Raju, “Thermal Analysis of Multi Tube Pass Shell and Tube Heat Exchanger”, International Journal of Innovative Research in Science, Engineering and Technology, vol. 3, Issue 11, November 2014, Pages 17605-17612.
[4]
Arun Kumar Tiwari, “Thermal Performance of Shell and Tube Heat Exchanger Using Nano fluids”, IJAPME, Vol. 1, Issue -1, 2015, 27-31.
[5]
Aphichat Danwittayakul, Cattaleeya Pattamaprom, “Investigation of Heat Transfer Efficiency of Alumina Nano fluids in Shell and Tube Heat Exchanger”, IPCBEE, Vol.82, 2015, pp. 68-72.
[6]
Sk. M. Z. M. Saqheeb Ali, k. Mohan Krishna, S. D. V. V. S. Bhimesh Reddy, sk. R. S. M. Ali, “Thermal Analysis of Double Pipe Heat Exchanger by Changing the Materials Using CFD”, IJETT, Vol. 26 Number 2, August 2015, pp. 95-102.
[7]
Mon M. S. and Gross U., “Numerical study of Fin-Spacing Effects in Annular-Finned Tube Heat Exchangers”, International Journal of heat and Mass Transfer, Vol. 47, pp. 1953-1964, 2004. 39.
[8]
Lars Davidson, “An Introduction to Turbulence Models”, department of thermos and fluid dynamics, Chalmers University of Technology, Sweden, 2009.
[9]
N. Sahiti, F. Durst, A. Dewan, “Heat transfer enhancement by pin elements”, IJHMT, vol. 48, Issues 23–24, November 2005, Pages 4738–4747.
[10]
Özden Ağra, Hakan Demir, Ş. Özgür Atayılmaz, Fatih Kantaş, Ahmet Selim Dalkılıç, “Numerical investigation of heat transfer and pressure drop in enhanced tubes”, International Communications in Heat and Mass Transfer, Vol. 38, pp. 1384-1391, 2011.
Browse journals by subject